Store

838-PEB PCB - PREORDER

$60.00
Sold out
Assembled/tested
Please choose
3D Printed PEB Card Rail Guides
Please choose
Mid Tower Case
Please choose
ATX Power Supply
Please choose
838-Latch Relay Module
Please choose
838-Drive Select Board
Please choose
838IO Plus Cable
Please choose
838-IOP 3D printed case
Please choose
838-32K for 838-IOP
Please choose
Geneve Video/keyboard/sound breakout board
Please choose
Micro USB Cable
Please choose
Save this product for later
Share this product with your friends

838-PEB PCB - PREORDER

Product Details

THIS IS A PREORDER ONLY!

Note: This preorder does NOT include shipping! Shipping will be sent in a separate invoice once the item(s) are ready for shipment. Items will not be shipped until the shipping invoice is paid. This is done to ensure the most accurate amount of shipping and packaging will be charged based on item(s) purchased.

Ordering options explained in the below linked video!
https://youtu.be/lkkmzmUmzXA

Preorder closes on August 31, 2022 @ 9:00 a.m. CST



Absolutely no refunds will be given once the preorder closes and components and/or PCBs have been ordered.



Components and PCBs will not be ordered until after the pre-order closes. PCBs and components will take ~3 weeks to be delivered once the orders are submitted. Expect PCBs and components to be ordered during the 1st week of September 2022.



This preorder is for a bare PCB unless additional options are added at time of purchase. See linked video above for explanation of all options.



The 838-PEB board allows a TI or Geneve user to choose their own PC ATX case and ATX power supply (24 pin) to be used based on the user's needs. In order to keep cost down and to allow the user to customize their unit the buyer must buy their own PC case and ATX power supply this unit does not come with unless added as option.



The case offered will be a ATX Mid-Tower case (not included unless selected as option) with

  • 2 x USB 2.0/USB3.0/Audio In/Out Front ports
  • 1 x 3.5" external Drive Bays
  • 3 x 5.25" external drive bays
  • 5 x 3.5" internal Drive bays
  • ATX Power supply mounts at top (not included)
If any of your PEB cards have had the voltage regulators removed and jumpered you will need to ensure you have added them back. I recommend 1.5 amp voltage regulators as 12v will be delivered to the 5v voltage regulators and be regulated by the voltage regulator down to 5.



The 838-PEB Board comes blank you may choose options for assembly.

This product has been designed around the 838-IO Plus card that replaces the Texas Instruments Flex Cable Interface. Depending on the case you choose, and purchase will depend on if you can use the existing 838-IO Plus PEB card (if you purchased it). If not, you will have to purchase the 838-IO Plus ATX version of the card, which is shorter to allow for the existing cables to be snaked through the standard PC IO slot and plug directly into the card.

The 838-PEB board has the below standard features:

  • 8 x Expansion Slots
  • USB Pass through Power
  • USB Standby Power
  • 4 x 12v Fan headers
  • 1 x 12v tap
  • 2 each of 3.3v and 5v power taps
  • Front USB3 connector for power and data use
  • Connects for Gotek1 and Gotek2 drives for external mods for use with Display and Rotary. USB Data Lines (D and D-) hooked to front USB ports for use with MicroGotek or other USB hardware
  • RJ45 connected to Gotek1 and Gotek2 rotary and display headers for external hookups
  • Power Switch and Power LED hookups
  • connector for use with 838-Latching Relay Module

The 838-Latching Relay Module is required if a user will use the existing momentary power switch that all PC cases are equipped with. This module allows the momentary switch to act as a latching switch. Press to power on, press to power off. If the Latching relay module is not purchased, then the switch will have to be replaced with a latching switch to ensure the ATX power supply stays on.

838-PEB Manual:
http://www.shift838.com/downloads/838-PEB_manual.pdf

Videos of the product below:

838-PEB Part 1: Introduction
https://youtu.be/Kap86ksHbUE

838-PEB Part 2: Demonstration
https://youtu.be/xh1Mq1HeC8M



If you want to print your own 3D case for the 838-IO Plus sideport card then there are two that have been designed are in the linked file below:



http://shift838.99er.net/downloads/838IOPCASES.zip

Customer reviews
No reviews yet. Only signed-in customers who bought this product can leave reviews. To leave a review, sign in